- Used to ream and face BB86/92 bottom bracket shells to an ID of 40.98mm - Used in conjunction with HTR-1 head tube reaming and facing set (PK-6710), 750.2 centering cone adapter (PK-6735) and 690-XL facing cutter (PK-6730)
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")
The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.
A daily-use, shop version of Park Tool's world-famous CM-5.2 Chain Scrubber. The CM-25 features a super-tough die-cast aluminum case and handle, plus a unique brush/sponge replacement cartridge that makes it easy to keep it running smoothly and working properly. Park Tool's proven four-sided scrubbing action makes thoroughly cleaning chains quick and easy. A shop quality cleaner built to give years of constant use. - Proven chain scrubbing technology leaves chains sparkling clean - Durable A380 aluminum die cast case and removable handle - Dual-sided sponges and wicking pads to help reduce drips - Rotating brushes clean on all four sides of every link - Brush and sponge cartridge quickly and easily clicks in and out (RBS-25) - Locking cover with stainless steel hinge pins - Choose drip or immersion fluid application methods - 100% serviceable
Quickly, safely and easily set your crown race on 1.5-inch steerer tubes with Park's CRS-15 Crown Race Setting System. Specifically engineered for oversized steerers, the CRS-15 comes with one setting tube and a 1.5-inch inset that ensures full contact with the crown race for precision installation.
The key to wheels that are strong and reliable is having spokes that are properly and uniformly tensioned. Park's Spoke Tension Meter accurately and reliably measures the absolute tension of each of the spokes in a wheel, as well as the relative tension between all the spokes in a wheel. It's easy to use, affordable and it works on nearly any bicycle spoke, no matter its diameter, material or shape.
Engineered for fit, function, and leverage, these L-shaped shop-quality hex wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Straight hex shaft on the short side, ball end on the long side - Includes 2, 2.5, 3, 4, 5, 6, 8, and 10mm - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization
Engineered for fit, function, and leverage, these L-shaped shop-quality Torx compatible wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Torx compatible drivers at each end - Includes T6, T8, T10, T15, T20, T25, T30, and T40 - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization
Take the guesswork out of installing cables, wires and housing inside the frame. The IR-1.2 speeds the internal frame routing of electric wires, shift cable/housing, brake cable/housing and hydraulic tubing on carbon fiber, titanium, and aluminum frames. Kit includes four plastic-coated 250cm cables with attached magnets and unique fittings plus an external guide magnet to speed operation. Newly updated to include a dedicated E-tube Di2 cable connector that easily pulls through a 6mm frame hole. Opposite polarity magnets on cables seek and attach inside frame tubes, making it easy to route through frame entrances and exits. Works with any size frame including tandems. A true time and frustration saver!
Park's Torx Wrench Set includes T-handled T6, T8, T10, T15, T20, T25, T30 and T40 Torx wrenches with offset handles made from durable nylon in a comfortable, ergonomic design. The wrenches are made of high-torque industrial steel for exceptional durability. Plus, this set of super tools comes with a wall mount for easy access.
Securely holds any of Park's TS-2, TS-2.2, and TS-2.2P Professional Wheel Truing Stands and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
Securely holds the TS-4 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
Suspension maintenance and tuning require tools designed for a precise fit. The SKT-6 from Park Tools is a shop-quality set of six flat-faced sockets designed for use with common suspension fork fittings. Ideal for use with Park Tool Torque Wrenches, the 3/8-inch drive sockets are forged from tough chrome vanadium steel and chrome plated for lasting durability. - 24, 26, 27, 28, 30, 32mm flat-faced sockets - All sockets are 3/8" drive - Note: 27mm socket is tapered for better access on Suntour suspension forks
$29.95 - $49.95
Frame and Fork Taps will become a lifesaver at some time for virtually every mechanic. These taps are made of high-carbon steel and are precision ground. Park Tool Frame and Fork Taps cut easily and fit conventional tap handles.
Park Tool's 750.2 Centering Cone Adaptor increases the size of the centering cone of the HTR-1 and HTR-1B Headtube Reaming and Facing Sets. The 750.2 will allow you to use the HTR-1(B) to ream and face head tubes designed to accept IS, ZS, and 1.5-inch EC headset standards. Before reaming or facing, make sure you have the correct cutting tool and pilot for the headset standard(s) you are using. Please refer to our product pages for cutters and pilots for this detailed compatibility information.
The Park Tool SBS-1.2 is a shop-quality set of sockets, hex bits, and Torx style bits, selected specifically for common bike repair needs. Ideal for use with Park Tool torque wrenches, the SBS-1.2 3/8" drive bits and sockets are made from tough, chrome vanadium steel for lasting durability.
Park Tool's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press which is sold separately) BB86, BB90, BB92 and Press Fit bottom brackets from Shimano, Race Face, SRAM and others that use a nominal 24mm-diameter spindle. This tool has a bearing remover that fits inside the bottom bracket shell and into the bearing so the bearings can be tapped out of the frame with a hammer. The set also includes two bushings that you use in conjunction with a bearing press for precision bearing installation (bearing press sold separately).
$18.95 - $42.95
The MT-10, 20, 30 and 40 are high quality folding take-along tools that feature forged aluminum side plates, a mix of hardened and plated tools, and smooth ergonomic operation.
Shop quality preset torque driver that limit torque applied to fasteners, preventing over tightening and damage to lightweight components. The PTD-4/PTD-5/PTD-6 feature all metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at our factory in Minnesota. - ¼ inch hex drive - Includes 3, 4, 5mm and T25 bits stored in the handle - Limits torque applied to fasteners while rotating clockwise - All metal internal construction for long life
Park's Screw-Type Chain Tool is the ideal shop tool for easy and reliable chain maintenance and repair. The sliding shelf makes it compatible with 1/8th-inch chains and all 3/32nd-inch chains, from 5- to 11-speed. It's made from investment-cast tool steel and has long vinyl-coated handles and fine threading for easy chain pin removal. It also includes a stiff-link loosener and comes with an extra pin.
Big and powerful, Park's Adjustable Wrench is forged from steel and chrome plated for maximum durability. Its jaws open up to 36mm and the torque-friendly, 12-inch handle is vinyl dipped for comfort.
Park's Professional Pedal Wrench features an angled, oversize head for maximum leverage. It has two 15mm wrenches at different angles, so you can maximize your leverage, and a long, round, vinyl-coated handle that won’t dig into your hand the way flat wrenches do. There's even a hole in the end for hanging the wrench on your toolboard.
Precision component screwdriver machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined and hard anodized 6061 aluminum handle.
Park Tool's Utility Pick Set is a set of three unique, multi-purpose picks ideal for a wide variety of detail work. Features: • Aluminum handle with magnet • Picks are replaceable, cold formed, heat treated and polished high carbon steel • Set includes 1-straight, 1-hook and 1-90 degree pick
Park's Folding Chain Tool is a heavy-duty tool-steel shop-quality chain tool that also folds for carrying in your pack or pocket for use on the road and trail. It's compatible with 9-, 10- and 11-speed chains. It also includes a folding peening anvil for Campagnolo 11-speed chains.
Park's I-Beam Mini Fold-Up Hex Wrench/Screwdriver/Torx Set with Chain Tool includes 1.5, 2, 2.5, 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen, a regular screwdriver, a T25 Torx tool (for disc-rotor bolts), a tire lever, spoke wrenches and a chain tool. The I-Beam conveniently fits in pockets and packs, too.
To prevent poor shifting and uneven drivetrain wear, most manufacturers recommend chain replacement at or before 1% stretch. Now you can quickly and accurately determine the wear and stretch of any chain with Park's Chain Checker. Simply insert the Chain Checker’s pins into 2 links, press the swingarm gauge tight, and then check the gauge window for an accurate reading!
The Park Tool FWS-2 Fold-Up Wrench Set combines all the popular hex and Torx compatible wrench sizes of the AWS-10 and TWS-2 into one convenient set. The multi-position shop grade fold-ups are comfortable, lightweight, slip-resistant, and 40% stronger than steel handles. Made in USA.
• Precision CNC-machined aluminum tool for the installation and removal of external bearing bottom brackets • Anodized for easy identification and featuring a ratchet/ torque wrench compatible 3/8” drive • Fits 16 notch adaptors measuring 39mm diameter such as Shimano XTR BB93, Dura Ace BB9000
Page 1 of 4 Next page